Battery Material Solution Profile

Advanced cathode, anode and electrolyte materials engineered for high-energy-density batteries.

From lab-scale R&D to industrial mass production, we provide certified materials with traceable quality for EV and energy storage applications.

Thermal Interface Materials

Precision-engineered thermal solutions for demanding electronics and power systems.

Conductive pads, compounds and films validated by independent labs for consistent long-term reliability.

Interface
Cell & module to cold plate
Materials
Thermal, barrier, insulation and sealing
Manufacturing
Die-cutting, dispensing and adhesive backing
Validation
Thermal cycling, vibration and aging
Interface Mapping

Map Every Interface Inside the Battery System

Each material is chosen against the interface it actually touches — the metal, the board, the busbar and the enclosure.

Primary thermal path

Cell & Module to Cold Plate

Pads, gap fillers and TIM layers manage compression, gap variation and heat flow at the cooling interface.

Thermal interface options
Control & sensing

BMS & Control Electronics

Potting, coating, local TIM and sealing protect boards, sensors and connectors from heat, moisture and vibration.

Electronics protection
High-voltage & busbar

Inverter, Busbar & Power Conversion

Insulation film, dielectric parts and thermal interface for high-voltage and power-conversion areas.

Insulation & dielectric
EV BATTERY PACK

Battery Pack Material Function Map

  1. 1
    Module-to-cooling interfaceThermal pad / TIM
  2. 2
    Local gap-filling areaLiquid thermal gap filler
  3. 3
    Cell-to-cell areaAerogel / thermal barrier sheet
  4. 4
    HV / busbar areaInsulation film / dielectric parts
  5. 5
    Pack cover & tray flangeGasket / sealant / FIPG
  6. 6
    BMS / electronics areaCoating / potting / local TIM
  7. 7
    Connector & cable entrySealing / protection parts
  8. 8
    Pack structureAdhesive / bonding support
Battery pack material function map

The same material family may appear at several levels — selection is always reviewed against the specific position and function.

Material Families

Choose the Function Before the Chemistry

Six functional families cover thermal, insulation, sealing, bonding and protection needs across the pack.

01

Thermal Gap Fillers

  • Dispensed or pre-cured
  • Fills uneven gaps
  • Low compression stress
Explore
02

Thermal Pads

  • Defined thickness
  • Clean, dry assembly
  • Easy rework
Explore
03

Thermal Adhesives

  • Bonds and conducts
  • Structural thermal joints
  • Controlled bond line
Explore
04

Insulation & Barrier

  • Dielectric film
  • Thermal barrier sheet
  • HV / busbar protection
Explore
05

Bonding & Structural

  • High shear strength
  • Pack structure and brackets
  • Gaskets and FIPG
Explore
06

Potting & Encapsulation

  • BMS and PCB protection
  • Coating and sealing
  • Moisture and vibration
Explore
System Levels

Material Focus by System Level

Material selection reviewed by system level — the same family may serve several levels.

01
Cell Level
Cell-to-cell barrier Insulation film Cushion / compression pad Side protection
02
Module Level
Thermal pad / TIM Compression pad Barrier sheet Sensing support
03
Pack Level
Cooling interface Enclosure sealing HV insulation Structural bonding
04
Rack / Container Level
Rack barrier Cable-entry sealing Enclosure protection Outdoor durability
Format Comparison

Match the Material Format to the Interface

The same function can be delivered as a pad, a paste or a film — the interface decides which fits best.

Material formatBest-fit interfacePrimary advantageDesign watch points
Gap fillerUneven or large gapsConforms at low pressureDispense control, cure, pump-out
Thermal padFlat, defined gapsClean assembly and reworkCompression set, tolerance stack
Thermal adhesiveStructural thermal jointsBonds and conducts at onceCure schedule, bond-line thickness
Insulation filmHV / busbar areasThin dielectric barrierPuncture, creepage, temperature
Bonding adhesivePack structureHigh shear strengthSurface prep, fixture time
Potting compoundBMS / electronicsFull encapsulationVoids, thermal expansion, rework
Selection Brief

Build the Material Brief in Five Steps

A clear brief turns an interface description into a material and format we can sample and test.

STEP 01
Define the Heat Path

Locate where heat is generated, spreads and leaves the pack.

STEP 02
Measure the Gap

Capture the real gap range, flatness and surface finish.

STEP 03
Set Stress Limits

Define allowed compression, movement and vibration.

STEP 04
Choose the Process

Match format to dispense, cure and assembly method.

STEP 05
Validate Reliability

Confirm the interface through cycling and aging.

Before You Sample

What Should Be Specified Before Sampling?

Give these six inputs and the first sample is far more likely to fit on the line.

01

Thermal Target

Heat load and allowed temperature rise at each interface.

02

Gap & Contact Area

Gap range, flatness and contact footprint.

03

Pressure & Motion

Compression limits, swelling and vibration.

04

Electrical Isolation

Dielectric strength and creepage distance.

05

Environmental & Aging

Temperature, humidity and cycle life.

06

Manufacturing

Dispense, cure and assembly constraints.

Have these six inputs ready? Send a clearer material brief
Failure Prevention

Design Around the Risks That Appear After Assembly

Most interface problems appear only after build and cycling — plan for them up front.

Risk

Excessive Compression Stress

Over-tightening or hard pads load cells and boards.

Mitigation
Risk

Contact Loss After Cycling

Thermal cycling relaxes the interface over time.

Mitigation
Risk

Insufficient Dielectric Margin

Thin or damaged film breaks down under HV.

Mitigation
Risk

Inconsistent Dispense / Voids

Air pockets and uneven beads hurt heat flow.

Mitigation
Risk

Migration / Contamination

Oils and fillers migrate into sensitive areas.

Mitigation
Risk

Cure Stress & Potting

Shrink and expansion stress boards and joints.

Mitigation
Battery Platforms

Different Architectures, Different Material Priorities

Cell format and pack architecture shift which interface dominates the design.

01 / Cell format

Prismatic

  • Rigid cans
  • Defined compression
  • Large cooling plates
02 / Cell format

Pouch

  • Thin, swelling cells
  • Soft pads
  • Low-pressure fillers
03 / Cell format

Cylindrical

  • Curved contact
  • Conformal fillers
  • Cell holders
04 / Rack & container

Storage & ESS

  • Rack / container scale
  • Barrier and sealing
  • Outdoor durability
Validation Plan

Test the Final Interface, Not Only the Material

Material data is a start — the assembled interface is what has to survive.

Test

Thermal Performance

Interface resistance under real load.

Test

Compression Behavior

Deflection and recovery at set pressure.

Test

Electrical Safety

Dielectric strength and insulation resistance.

Test

Environmental Aging

Heat, humidity and thermal cycling.

Test

Mechanical Reliability

Vibration and shock endurance.

Test

Production Capability

Dispense, cure and repeatability.

Manufacturing & Customization

Material Performance Must Survive Manufacturing

A material only works if it survives dispense, cure, cutting and assembly on your line. Share equipment constraints, annual volume, package size and dispense or die-cut drawings early, and the format is built around your process.

Explore customization capabilities

Custom Formulation

Tune conductivity, modulus and cure to the interface.

Die-Cut Conversion

Pads, films and gaskets cut to drawing.

Dispensing Support

Process parameters for beads and gaps.

Prototype Samples

Fast samples for trial builds.

Engineering Resources

Build a Stronger Battery Material Specification

Use these guides to define interface geometry, compare material formats and prepare a practical validation plan.

Thermal Interface

How to Choose a Thermal Interface for EV Packs

Compare pads, gap fillers and dispensable TIM against gap, pressure and rework.

Read the TIM selection guide
BMS Interface

Protection Materials for Battery Management Systems

Understand coating, potting and local TIM around BMS heat sources and connectors.

Read the BMS guide
Gap Strategy

Dispensable Gap Filler Vs. Thermal Pad

Compare variable-gap conformance, clean placement, pressure and rework.

Compare material formats
Geometry

How Bond-line Thickness Affects Performance

See why actual interface thickness belongs in every thermal comparison.

Review bond-line effects
Selection

Why High W/mK May Not Mean Better Cooling

Balance conductivity with thickness, pressure, wetting and reliability.

Read the selection guide
Product Directory

Browse MIWAKEE Material Families

Review available thermal, barrier, insulation and sealing families.

Browse all materials
Frequently Asked

EV Battery Thermal Material FAQ

Quick answers to the interface questions we hear most.

What thermal material is used between a battery module and a cold plate?

A thermal pad or gap filler sized to the real gap and compression.

How is the right gap filler thickness chosen?

From the measured gap range plus the target compression.

Does a pad or a dispensed filler suit large gaps better?

Dispensed fillers conform better to uneven, larger gaps.

Can one material provide both insulation and thermal transfer?

Some films and pads do, but check dielectric strength and thickness.

What data should be requested before sampling?

Thermal, dielectric, mechanical and compliance data, plus process guidance.

Send the Gap, Heat Load, Voltage and Production Process

Share your interface and we will recommend a material and format.

Request a material recommendation